About Our Deck Building & Repair Service
Worn deck boards are a surface problem. A deck fails at its connections: an unflashed ledger rotting out of sight against the house, or footings that stop above the frost line and heave in a hard freeze. As a Garfield-based deck builder, we build new outdoor decks, replace worn-out ones and repair the ones worth saving. New Jersey's 2024 residential code, in force since August 17, 2026, spells out for the first time how a deck ledger must be flashed, and confirms that the state, not your town, sets the frost depth. That flashing is roofing and siding work, the trades our crew already does.
Deck Repair, Resurfacing or Replacement: How Do You Tell?
Replace a deck when decay has spread through the ledger, joist ends or posts; repair it when rot is limited to a few members; resurface it only when the whole frame tests sound. Decks come down at the connections: ledger to house, posts to footings, joists to hangers. Checks you can do yourself:
- Probe the ledger, joist ends, post bases and beam seats with a screwdriver. Sound wood splinters; decayed wood lets the tip sink in and breaks short, across the grain.
- Look for rust streaks under lag heads and flaking or half-nailed hangers.
- From the basement, look for water stains or soft spots on the band joist behind the deck.
- Look for a gap at the ledger, a ledger lagged straight into brick, or a ledger hung on a cantilever, where the house's floor joists run out past the foundation wall, so the band joist the deck hangs from has no wall under it.
- Look for hold-downs, usually a metal bracket on a joist near each end of the ledger with a rod or strap through to a floor joist inside. Missing ones aren't proof of failure, but they're a reason to have the connection checked.
Composite boards carry a label with their maximum span. If your joists are spaced wider, re-decking becomes re-framing.
Why the Ledger Is Where North Jersey Decks Fail
The ledger, the board fastened to the house that carries one side of the deck, is a North Jersey deck's weak point: the seam above it takes water from every nor'easter, and an unflashed ledger rots along with the house's band joist behind it. The 2024 NJ code now spells out the flashing (R507.9.1.5):
- Corrosion-resistant flashing (metal at least 0.019 inch nominal thickness), running at least 2 inches up the wall.
- At the bottom, at least 4 inches past the ledger face, or to the face and at least 1/4 inch down it.
- Where a door or window sits less than 2 inches above the ledger, it runs to the bottom of the opening.
- No flashing where the ledger is held at least 1/4 inch off the wall covering so water drains behind it.
The flashing laps into or is sealed to the water-resistive barrier, and an old wall with none gets one behind the ledger. Tape on the ledger face isn't flashing. Vinyl siding must now stay at least 1/2 inch clear of the deck; siding repair covers patching and matching after the wall is opened.
The code bars toenails and nails that can pull out; ledgers take 1/2-inch lag screws or bolts in predrilled holes, or other approved fasteners. The deck also needs a lateral connection to the house. The code's standard method is hold-downs: two rated at least 1,500 pounds within 24 inches of each end, or four rated at least 750 pounds, evenly spaced with one within 24 inches of each end.
On a brick-front house, check whether the brick is veneer. The code bars supporting a ledger on stone or masonry veneer, a non-structural facing tied to the framing behind it. The options are an approved attachment through to that framing, or a freestanding deck. Some pre-war houses have solid masonry walls rather than veneer. Rows of bricks laid end-out every few courses often point to a solid wall, but only a look inside the wall or a designer's check confirms it. How a ledger anchors to solid masonry is for the designer and construction official. Some towns bar ledgers on cantilevered floors (Manalapan, in Monmouth County, for one).
Why a Roofing and Siding Crew Builds Decks
The hardest part of a deck is the house side. On a sided wall, the siding comes off at the ledger line, the flashing ties into the barrier behind it, and the siding goes back with its 1/2-inch clearance. Our crew does roofing, siding, gutters and masonry, so the wall above the ledger, the gutter dripping onto the deck and the brick stoop at the foot of the stairs are one job. A heaved or crumbling stoop is masonry work to fix before stairs land on it.
How Deep Do Deck Footings Go in North Jersey?
For a deck attached to the house, footings must be frost-protected, which normally means reaching the frost line: 36 inches in Bergen, Passaic, Essex, Hudson, Morris and Union counties. New Jersey has only two frost depths, 36 inches north and 30 inches south, and the 2024 NJ edition deleted the footnote some towns had read as letting them set their own.
Wet soil expands as it freezes, so a pier that stops above the frost line can lift in a hard freeze and settle unevenly in the thaw. Clay soils, common in parts of North Jersey, hold that water longer. The result is racked railings, a misaligned threshold, a ledger pried off the wall. Extend downspouts past the deck; gutter guards keep a clogged gutter from spilling onto it. The footing inspection happens with the holes open, so ask for a photo of a tape measure in each hole before the pour.
Freestanding decks have a state minimum of 12 inches below undisturbed ground. Two kinds of freestanding deck need no footings: joists resting on grade along their full length, or joists on precast pier blocks at grade with no beams or posts, if the deck is at most 200 square feet and within 20 inches of grade at every point within 36 inches of its edge. Towns can't change the frost depth, but their guidelines may still ask for 36-inch footings; confirm with your construction official. For a surface at grade, a paver patio may serve better than a low deck.
Pressure-Treated, Composite or Cedar: What Differs and What to Check
All three work in New Jersey when installed to their own rules. What differs is how they age and what upkeep they need:
- Pressure-treated: boards check, cup and turn gray, and need cleaning and stain on a schedule. The end tag shows the use category; the American Wood Protection Association assigns ledgers and posts to Ground Contact (UC4A or higher), boards, rails and stairs to Above Ground (UC3B or higher).
- Composite: no stain, but it moves with temperature, gets hot in July sun and scratches; check the care guide before using ice melt. Boards must carry an ASTM D7032 label showing maximum span, and joist spacing and gapping follow the maker's installation manual.
- Cedar and redwood: only heartwood counts as naturally durable; it dents easily and grays without a finish.
- Hardware: hot-dip galvanized, stainless or another type the code's fastener table lists, rated by its maker for contact with treated lumber. Stainless is required within 300 feet of a salt-water shoreline, which can reach Hudson County waterfront lots; whether a tidal river counts is the official's call.
Under any surface the frame is usually pressure-treated, so the frame checks above still apply.
Do You Need a Permit for Deck Work in New Jersey?
A new deck or total replacement needs a construction permit; like-for-like repair usually doesn't. Under N.J.A.C. 5:23-2.7, part of New Jersey's Uniform Construction Code (UCC), repairing or replacing any part of a deck that doesn't support a roof or part of the building is ordinary maintenance, if the new material is identical or closely similar and goes in the same place.
- Like-for-like boards, joists or posts in the same place: ordinary maintenance under the state rule, so normally no construction permit.
- A different material (wood to composite) or new layout: may fall outside it; ask first.
- A new deck, total replacement or expansion: full permit. The state's 'minor work' category covers porches and stoops, not decks.
- A deck that supports a roof: outside ordinary maintenance. Roofed porches are on our porches and steps page.
- Guards: some towns, Ringwood for one, still want a permit even for like-for-like guard replacement; check with your construction official.
Some towns want zoning or prior approval before the construction permit (Ringwood's published deck procedure does), and town checklists such as Verona's ask for a property survey showing setbacks. Inspections typically come at footings, framing and final. A complete application, prior approvals included, filed by February 17, 2027 can still use the 2021 codes.
On narrow lots in Garfield, Clifton and Hudson County, check fire separation before you design. DCA's guidance on the 2024 code says a deck with a fire separation distance of 2 feet to less than 5 feet needs a 1-hour fire-rated underside, heavy timber, or fire-retardant-treated wood labeled for exterior use. Coatings applied later don't count. Closer than 2 feet, talk to the construction official before anything is designed; the official confirms how the rule applies either way.
Who Draws Deck Plans, and Which Decks Need an Engineer?
New Jersey deck permit drawings need the seal of a NJ-registered architect or licensed engineer, unless a homeowner prepares them, by affidavit, for the detached single-family house they live in, or the construction official waives plans for minor work. That exception doesn't cover new construction or substantial improvement in a flood V zone. Owners of two-family houses, common in Garfield, Passaic and Clifton, should expect to need sealed drawings; confirm with the construction official. A contractor's registration doesn't let anyone seal plans. We're a licensed home improvement contractor (NJ HIC #13VH12696700), not a design firm, so if anyone offers to 'do the drawings', ask whose seal will be on them.
Hot-tub decks, decks carrying an outdoor kitchen, long-span, tall or multi-level decks, and stacked decks serving both units of a two-family house often need an engineer's design; the code's standard deck rules cover only ordinary decks and loads. Apartment-style buildings of three or more units (townhouses aside) fall under the International Building Code (IBC) instead.
What Inspectors Check on Railings and Stairs
Inspectors check railing height, baluster gaps, handrails, the landing and deck lighting, and town checklists spell out the detail. Two New Jersey examples:
- Verona (Essex County), in a checklist written to the 2021 code: a graspable handrail on stairs with more than three risers, a concrete or paved pad extending 3 feet from the bottom riser, a switched light at every door onto the deck and a receptacle on the deck.
- Manalapan: railings at least 36 inches high, balusters less than 4 inches apart, a graspable handrail at four or more risers, hardware rated for treated lumber.
Lights and receptacles need an electrical permit, and wiring done for hire needs a licensed electrician. Get your town's deck checklist before drawings are made.
What a Deck Replacement Involves, Step by Step
A full replacement runs in this order:
- Approvals: survey, zoning, drawings, permit. N.J.A.C. 13:45A-16.2 bars a home improvement contractor from starting before permits issue.
- Tear-out: pressure-treated decks built before 2004 are likely CCA-treated (arsenic-based). EPA advises against burning it or reusing it as mulch and says to wear goggles and a dust mask when sawing it; it can usually go in ordinary trash, subject to local rules.
- House wall: open the siding, repair rotted band joist or sheathing, install barrier and flashing.
- Footings: 36 inches for an attached deck, inspected before the pour.
- Framing: fasteners, hold-downs, beams, joists and hangers, inspected while visible.
- Finish: decking, guards, stairs, any wiring by a licensed electrician, then final inspection. Copies of the inspection certificates come to you before final payment.
What to Check Before You Sign or Pay
When quotes differ widely, check the low one first for house-side flashing, hold-downs and full-depth footings. Signs of a deck built right:
- Flashing tucked behind the siding above the ledger
- Lags, bolts or other approved fasteners staggered into the house framing, with hold-downs near each end
- Ground-contact tags on the posts and ledger
- Hangers nailed out with the fasteners their maker specifies
Signs to stop and ask:
- A ledger on brick veneer or a cantilevered floor
- Nails into the house, or uncoated hardware against treated lumber
- Posts buried without ground-contact treatment
- Pier blocks under a raised deck
- Work that started before the permit
Above the statutory dollar threshold, New Jersey requires a signed written contract with the work, principal materials, total price, start and completion dates, and any warranty. Ours includes a written workmanship warranty; our NJ license and insurance details are posted. Start with a free written estimate; financing is available and explained at the estimate.
What's Included
- New outdoor decks and full tear-out replacements
- Repairs to boards, railings, stairs, joists and posts
- Flashed ledgers fastened to house framing, with lateral hold-downs
- Footings to the 36-inch frost line on attached decks
- Stairs with graspable handrails, guards and a solid landing
- Free written estimates with the scope spelled out
Deck Building & Repair — Common Questions
Do I need a permit to replace deck boards in NJ?
Usually not, if the replacement is like-for-like. N.J.A.C. 5:23-2.7, part of the Uniform Construction Code, treats repair or replacement of any part of a deck that doesn't support a roof as ordinary maintenance, provided the new material is identical or closely similar and goes in the same location. That covers joists and posts as well as boards. Switching from wood to composite or changing the layout may take the job outside that rule, so ask your construction official first. Some towns, Ringwood for one, also want a permit for replacing guards alone.
Do I need a permit to build or replace a whole deck in New Jersey?
Yes. A new deck or a total replacement isn't ordinary maintenance, so it needs a construction permit, and because the state's 'minor work' category covers porches and stoops but not decks, it goes through the regular permit process. Some towns also require zoning or prior approval first, and checklists such as Verona's ask for a property survey showing setbacks. After the permit issues, inspections typically come at three points: footings with the holes open before concrete, framing before the decking hides it, and a final. No home improvement contractor may start before the permit is issued.
Do I need a permit for a freestanding deck in New Jersey?
Plan on one. Ordinary maintenance covers repairs to an existing deck, not a new one, so a new freestanding deck goes through the regular construction permit process like an attached deck. What changes is the footing: the state minimum for a freestanding deck is 12 inches below undisturbed ground instead of the 36-inch frost depth an attached deck needs in North Jersey, though some towns' guidelines still ask for 36. Confirm both with your construction official before you build.
How deep do deck footings have to be in North Jersey?
For a deck attached to the house, frost-protected, which in North Jersey normally means 36 inches. New Jersey has two frost depths, 36 inches in the north and 30 in the south, and Bergen, Passaic, Essex, Hudson, Morris and Union counties are all in the northern zone. Towns can't change the frost depth, though a town's deck guidelines may still ask for 36 inches on a freestanding deck. The state minimum for freestanding decks is 12 inches below undisturbed ground, and small, low freestanding decks on precast pier blocks can skip footings. Confirm with your construction official.
Can a deck be attached to a brick house?
Not to brick or stone veneer. The 2024 New Jersey residential code says a deck ledger can't be supported on veneer, a non-structural facing tied to the framing behind it, so the options are an approved attachment through to that framing or a freestanding deck on its own posts and footings. Whether a solid brick wall, found on some pre-war houses, can carry a ledger is a design question for your designer and construction official.
Should I repair my old deck or replace it?
It depends on the frame and the house connection, not the boards. Probe the ledger, the joist ends and the post bases with a screwdriver; wood that lets the tip sink in and breaks across the grain is decayed. Check the band joist from the basement for water stains. If those test sound, repairs or new boards make sense. If decay has spread through them, new boards on that frame are money spent on the wrong part. Missing hold-down hardware is another reason to have the connection checked.
My deck is pulling away from the house. What should I do?
Keep everyone off it until it has been checked. A gap at the ledger means the connection carrying the house side of the deck is letting go. From the basement, look for wet or soft band joist behind the deck, which tells you water has been getting in. If a storm or a falling limb caused it, photograph everything before anything is moved; we document storm damage for your own insurance claim, and one visit can check the roof edge above it as well.
Composite or pressure-treated: which holds up better in New Jersey?
Neither wins outright; they age differently. Pressure-treated boards check, cup and gray unless they're cleaned and re-stained periodically, and the end tag should show the right use category, Ground Contact for posts and ledgers per AWPA guidance. Composite needs no stain but moves with temperature, gets hot in summer sun and scratches; its boards must carry an ASTM D7032 label with their maximum span, and joist spacing and gapping follow the manufacturer's manual. Under either surface the frame is usually pressure-treated, so the frame and the ledger decide how long the deck lasts.
