About Our Fireplace Repair Service
We repair and restore masonry fireplaces in New Jersey: the firebox, smoke chamber, damper, hearth and surround. Open firebox joints are repacked with the refractory mortar the residential code calls for, not ordinary masonry mortar. A rough, stepped smoke chamber is parged smooth. A rusted damper is repaired or replaced, and the water that rusted it is traced to the top of the chimney. Hearths and surrounds are reset or rebuilt, and we check them against the clearances that keep heat off your floor and trim. The same family-owned crew works on chimneys and exterior masonry, so the whole system gets looked at once. Gas and electrical work goes to licensed partners. Our masons work from Garfield across North Jersey, including Bergen, Passaic, Essex, Hudson, Morris and Union counties.
Which Kind of Fireplace Do You Have?
Most homes have one of two kinds: a masonry fireplace (a firebrick-lined box, a masonry smoke chamber and a brick or stone chimney) or a factory-built (prefab) fireplace, a listed metal box lined with molded refractory panels. Our fireplace work covers masonry fireplaces, from the damper down into the room; the crown and flashing above the roof are under chimney repair and servicing. Two quick tells:
- Inside the firebox: mortar joints between individual bricks mean masonry. Large flat molded panels, with a metal firebox or metal top and sides behind them, mean factory-built.
- On the roof: a round metal pipe rising from a framed, sided chase means factory-built. A brick or stone stack usually means masonry, but a relined chimney can show a round metal liner on top, so let the firebox decide.
A factory-built unit is repaired with its manufacturer's parts under its listing, and patching a listed metal unit with mortar is not a repair. For a factory-built unit, call a service technician for that brand or the dealer who sold it. If there is no chimney yet and you want one for a fireplace or stove, start with new chimney installation.
What's Wrong With My Fireplace? Symptoms and Likely Causes
Each common fireplace symptom points to a different part: the firebox lining, the damper, the hearth and mantel, the brick above the opening, or the house itself.
- Loose, cracked or missing firebrick, or open firebox joints: the lining that keeps heat off the masonry and framing behind it has gaps. Have it evaluated before the next fire.
- Rust flakes on the hearth, a sticking damper, or water in the firebox after rain: water is usually getting in at the top, through a missing cap, a crown cracked by freeze-thaw, or failed flashing. Stop the water first; chimney leak repair covers tracing it.
- A warped damper plate: the Chimney Safety Institute of America (CSIA) lists it as a sign that a chimney fire already happened (see the damper section).
- A crack where the hearth extension meets the hearth, or an extension sunk below the floor: its support or the floor framing under it may have moved. Have that checked before the slab is reset.
- Scorched or blistered mantel paint: usually the mantel sits too close to the opening or projects too far for its distance (clearances below).
- A crack or sag in the brick right above the opening: the steel angle iron (lintel) carrying it may be rusting or bent. That is a masonry repair, not a firebox one; masonry repair explains how a rusting lintel cracks the brick around it.
If a buyer's home inspector wrote "recommend further evaluation" next to the fireplace, see what each chimney inspection level covers.
Firebox Repair or Rebuild: Refractory Mortar and 1/4-Inch Joints
Repair a firebox when the firebrick is sound and only joints or single bricks have failed; reline it when bricks are loose across a whole wall, the back wall has bowed forward, or the masonry behind the lining is exposed. Joints open from heat cycling, as the lining expands with every fire and shrinks as it cools, and from water coming down an uncapped flue. New Jersey's residential code calls for firebrick meeting ASTM C27 or C1261, laid in medium-duty refractory mortar meeting ASTM C199, with joints no wider than 1/4 inch. Ordinary Type N or S mortar is not that product, and neither is fireclay stirred into regular mortar. Exterior brick walls take lime or Portland mortar matched to their age instead.
Repair means raking out failed joints, repacking them with refractory mortar and replacing cracked or spalled firebricks. Relining means tearing out the lining and re-laying it in new firebrick, which keeps your firebox the size it is. The code's dimensions apply to a new or fully reconstructed firebox: back and side walls each at least 8 inches of solid masonry, including a firebrick lining at least 2 inches thick (10 inches with no lining), and a depth of at least 20 inches, or 12 for a Rumford fireplace built to its own proportions. These dimensions come from the 2024 edition of the residential code, which New Jersey adopted on August 17, 2026. Your construction official decides which rules a rebuild must meet. Repairs to an existing fireplace fall under New Jersey's Rehabilitation Subcode and may not reduce its existing level of safety, so an older firebox shallower than 20 inches is not a violation for that reason alone.
You can check the work with a flashlight: joints 1/4 inch or tighter, mortar kept off the brick faces, and no brick that moves when pressed. Color won't tell you which mortar was used, so ask for the product name and check that the bag or tub says ASTM C199.
Is Your Smoke Chamber Parged Smooth?
A smoke chamber built or rebuilt today must be parged smooth inside with ASTM C199 refractory mortar; an existing chamber that was never parged is not a code violation for that reason alone. The smoke chamber is the funnel above the damper that narrows the fireplace opening down to the flue. For a new or rebuilt chamber, the code also sets its walls at a total of at least 8 inches of solid masonry (6 with a firebrick or vitrified clay lining), with sloped walls leaning no more than 45 degrees from vertical and corbeled walls, stepped inward course by course, no more than 30. Work on an existing chamber falls under the same Rehabilitation Subcode as the firebox.
To check yours, open the damper and shine a light up past it. Brick ends stepping inward like an upside-down staircase mean an unparged, corbeled chamber; the ledges give soot and creosote somewhere to collect, and the sweep has to reach them. The repair is sweeping the chamber clean, then parging over the steps with refractory mortar into a smooth funnel, the finish the code calls for on new work. CSIA notes that a complete sweep includes the smoke chamber; chimney sweeping covers that cleaning.
Dampers: Repair, Replace, or Move It to the Top
A stiff damper with a sound frame can usually be freed and adjusted; a plate rusted through or warped means a new damper, and a damaged throat means repairing the throat and replacing the damper, or moving the seal to the top of the flue with a top-sealing damper. The code requires a ferrous metal damper at least 8 inches above the top of the opening, operable from the room, installed in the fireplace or in the chimney. So a top damper closed by a cable down to a handle in the firebox is allowed, installed per its manufacturer's instructions. Throat dampers fail in four common ways:
- A rusted plate, usually from water coming down the flue.
- A warped plate, which can mean a chimney fire. Don't light another fire until the chimney is swept and evaluated.
- A broken handle, chain or frame.
- A plate that moves but no longer seals, so heated air escapes all winter.
To check the seal, close the damper and hold a strip of tissue just below it; if the tissue flutters, air is getting past the plate.
CSIA says a tight-sealing top-mounted damper reduces air and odor coming down the chimney. The trade-offs: the cable hangs into the firebox, and the lid needs a sound flue tile and crown to seal on, so a cracked crown gets fixed first.
After a chimney fire, CSIA advises not using the chimney until it is swept and evaluated, and photographing the damage before it is swept. We can document it with photos and a written scope for your own claim. We don't negotiate or settle claims; in New Jersey that is you, a licensed public adjuster or an attorney. See documenting damage for a claim.
How Far Must a Hearth and Mantel Keep Heat From Wood?
For a masonry fireplace, New Jersey's residential code sets these distances:
- The hearth is at least 4 inches thick and the hearth extension at least 2 inches, with no wood forms or other combustibles left against their underside.
- The extension reaches 16 inches in front of the opening and 8 inches past each side, or 20 and 12 inches when the opening is 6 square feet or larger.
- Where the bottom of the firebox opening is raised at least 8 inches above the top of the hearth extension, a noncombustible extension as thin as 3/8 inch is allowed.
- Wood framing stays at least 2 inches from the front and sides of the fireplace masonry and 4 inches from the back.
- Combustible trim and the edges of sheathing may butt against the masonry beside the opening only if they are at least 8 inches from the inside face of the firebox lining. The distance is different for an opening of 6 square feet or larger, so confirm it with your construction official.
- Nothing combustible within 6 inches of the opening. Between 6 and 12 inches, trim may project only 1/8 inch per inch of distance, so a mantel edge 8 inches away may stick out 1 inch at most.
Our hearth and surround work is resetting or rebuilding cracked and sunken hearth slabs, extending short hearths, and rebuilding brick or stone surrounds. In older North Jersey houses we check for shallow hearths, wood flooring run under the hearth slab, and deep mantels added in a later remodel. Falling short of current clearances is not automatically a violation, but it is worth correcting when the hearth or surround is redone.
If your home was built before 1978, EPA's lead Renovation, Repair and Painting rule applies to most paid work that disturbs painted surfaces, such as a painted mantel, surround or the wall around them. Only small interior jobs (6 square feet or less of painted surface per room) are exempt, and never when painted material is demolished or paint is removed with power sanders or grinders. Covered work must be done by a firm certified by EPA or an authorized state or tribal program, following the rule's lead-safe work practices. We're an EPA Lead-Safe Certified firm with a certified renovator on our team, follow those practices on fireplace work the rule covers, and will show you our EPA RRP firm certificate before we start; ask the same of anyone else you're considering.
Restoring an Original Fireplace in an Older House
Restoring an old fireplace means making the original firebox, damper, hearth and surround sound and usable again, not replacing them. If your fireplace was boarded over or unused for years, before it is lit again we check:
- Whether the flue above it is lined and sound. A restored firebox under a cracked or unlined flue still isn't safe; chimney liner installation covers the fix.
- Whether a boiler or water heater was later connected to that flue. If it was, don't light the fireplace until the venting has been evaluated; the liner page linked above covers how those appliances are vented.
- Whether the damper still opens and seals, and whether the hearth and mantel meet the clearances above.
Original brick or stone on the surround is repointed with mortar matched to its age and color, the same lime-or-Portland matching used on exterior masonry, rather than hidden under new facing. Only the firebox lining takes refractory mortar.
Smoke in the Room? Rule Out the Simple Causes First
Smoke spilling into the room can be a house-pressure or firewood problem rather than a masonry one, so check these in order before paying for any rebuild:
- The damper isn't fully open.
- The flue is cold. Start with a small kindling fire so the flue warms and begins to draw before you add larger logs.
- The wood is wet. EPA says burn only dry, split, seasoned wood, ideally below 20 percent moisture, and never trash, cardboard, painted, treated or glued wood.
- The house is under negative pressure from kitchen and bath fans, a dryer or tight windows. Test it by cracking a window in the room once the fire is lit; if the smoke stops, the house is short of air, and CSIA's recommended fix is make-up air. The code requires new fireplaces to have an exterior air supply unless the room is mechanically ventilated to neutral or positive pressure; an existing fireplace without one is not automatically out of compliance.
- Then the masonry: a rough or stepped smoke chamber, or a chimney too short for its roof. A chimney inspection checks both.
If the cause is the house or the firewood, we'll say so rather than sell a rebuild.
Gas Logs and Conversions: What Needs a Licensed Plumber
In New Jersey, installing or repairing gas piping requires a licensed master plumber or master HVACR contractor. On our fireplace jobs that involve gas, that work and any electrical work is done by the licensed plumber and electrician we work with; our crew handles the masonry. What the logs themselves must meet depends on the fireplace:
- Masonry fireplace: gas logs must be a listed appliance (ANSI Z21.60, or Z21.84 for manually lighted natural-gas sets) installed per the manufacturer's instructions, which also govern how the damper is set. The firebox, damper and flue need to be sound before the logs go in.
- Factory-built fireplace: an unvented gas log heater or insert may not be installed unless the fireplace itself was tested and listed for that use. Its listing label and manual answer that, and its brand's service technician or dealer handles the work.
Changes to how a gas appliance vents are covered on the chimney liner page linked above.
Permits, Price and the Contract: What to Settle Before Work Starts
Before fireplace work starts, settle who pulls any permit, what the scope covers, and what the contract says. Your local construction official decides whether the work needs a permit. NJ's no-permit "ordinary maintenance" list excludes work affecting fire safety and any change to gas piping, and it doesn't name fireplaces, so ask the town before a firebox, smoke chamber or hearth rebuild or a new gas line.
We quote from a written scope after seeing the fireplace. The price moves with repair versus relining, smoke chamber parging, damper work, hearth work, any gas or electrical work by a licensed partner, and problems above the firebox such as a cracked crown. Whoever you hire, get these answers in writing:
- Which mortar, by product name, and does it meet ASTM C199?
- Is the firebox being repointed or fully relined, and is the smoke chamber in the scope?
- What happens, and how is it priced, if tear-out exposes damaged masonry behind the lining?
- Who pulls any permit?
New Jersey requires a home improvement contract over five hundred dollars to be written and signed, listing the work, principal products and materials, total price, and start and completion dates. Ours also carries our NJ HIC #13VH12696700 and our written workmanship warranty; see our credentials.
Every job starts with a free written estimate after we've seen the fireplace.
What's Included
- Firebox repointing and firebrick replacement in refractory mortar
- Firebox relining when the existing lining is past repair
- Smoke chamber parging to a smooth refractory finish
- Damper repair, replacement and top-sealing dampers
- Hearth, hearth extension and brick or stone surround repair
- Gas log jobs coordinated with a licensed plumber and electrician
Fireplace Repair — Common Questions
Is it safe to use my fireplace with cracked firebrick?
Not until someone has evaluated it, because the size of a crack alone won't tell you whether the lining still protects what's behind it. Firebrick is the layer between the fire and the brick and wood framing around the firebox, so a loose brick, an open joint or a gap you can see into means that layer may no longer be doing its job. CSIA, summarizing NFPA 211, the national chimney and fireplace standard, recommends inspecting chimneys and fireplaces at least once a year in any case. A sound repair replaces the loose or broken firebrick and resets it in refractory mortar; covering a missing or loose brick with a surface patch is not a repair.
What mortar should be used to repair a fireplace firebox?
Medium-duty refractory mortar to ASTM C199, laid in joints of 1/4 inch or less. That is the product New Jersey's residential code names for a firebox lining, and the firebrick itself should be ASTM C27 or C1261. Regular masonry mortar is a different material, and adding fireclay to it doesn't make it refractory mortar. You can't identify the mortar by looking at a finished joint, so have the contractor write the product name into the contract, then match it against the ASTM C199 marking on the package when it arrives.
Should I replace my old damper with a top-sealing damper?
It's worth considering when the throat damper is rusted through or warped, since the other option, a new damper in the throat, needs a sound throat to mount in. A top-sealer is a lid on top of the flue, worked by a cable from a handle inside the firebox. New Jersey's code permits the damper to sit in the chimney as long as it is ferrous metal and can be operated from the room, and the unit goes in per its manufacturer's instructions. Before choosing one, confirm the flue tile and crown it will close on are in good shape, and decide whether you mind the cable in the firebox.
Why does my fireplace smell in the summer?
Air is being pulled down the chimney and carrying the smell of the deposits inside it. CSIA describes this as a symptom of the whole house running at negative pressure. A sweep removes the deposits that smell, and a tight-sealing damper at the top of the chimney reduces the air coming down. A worn throat damper lets more of that air through; close the damper and hold a strip of tissue just below it, and if the tissue flutters, air is getting past the plate.
How far does a wood mantel have to be from the fireplace opening?
At least 6 inches for anything combustible, and farther for a mantel that projects. Under New Jersey's residential code for masonry fireplaces, combustible trim in the band from 6 to 12 inches away may stick out 1/8 inch for every inch it sits from the opening, so a mantel edge 10 inches above it can project no more than 1 1/4 inches. A factory-built unit's clearances come from its manufacturer's listing instead. An existing mantel that falls short is not automatically a violation, but scorched or blistered paint on it means heat is already reaching it.
Do I need a permit to repair a fireplace in New Jersey?
Possibly; the construction official in your town decides, based on what the work is. The state's exemption for ordinary repairs stops short of anything that affects structural or fire safety or alters gas piping, and it never mentions fireplaces by name. Before work starts, phone the construction office, describe the job in a sentence (for example, "relining the firebox in refractory mortar" or "new gas line for gas logs"), and ask whether a permit is needed. Then write into the contract which party, you or the contractor, applies for it.
Can you convert my wood fireplace to gas logs?
Yes, as a team: we check and repair the firebox, damper and hearth, and the licensed plumber we work with runs the gas line and connects the logs, with a licensed electrician for any wiring. New Jersey reserves gas piping work for licensed master plumbers and master HVACR contractors, which is why that part isn't ours. Pick a log set listed to ANSI Z21.60, or to Z21.84 if it is a manually lighted natural-gas set, and follow its instructions for the damper setting. A factory-built fireplace is a separate question; its own listing decides whether unvented logs can go in.
We're selling and the inspector flagged the fireplace. What now?
Get a written scope that separates safety items from cosmetic ones, so the buyer and seller are negotiating over facts. Open firebox joints, a failed damper or a hearth short of current clearances are safety items; staining is usually cosmetic. For what each level of chimney inspection covers, see [chimney inspection](/chimney-inspection-nj). Separately, New Jersey requires a smoke alarm, carbon monoxide alarm and portable fire extinguisher compliance certificate before a one- or two-family home is sold or leased, and homes with a fuel-burning fireplace need carbon monoxide alarms near the sleeping areas.
