24/7 Emergency Roof & Storm Response(201) 779-3961
Skip to main content
Chimney Installation in New Jersey by Tri-State Roofing and Chimneys

New Chimney Installation in New Jersey, Built to Code

New masonry chimneys built to NJ code, from the footing up to the crown.

About Our Chimney Installation Service

Chimney installation is construction, not a repair. A new masonry chimney in New Jersey needs a construction permit, a footing at least 3 feet below grade in the northern half of the state, and a stack built to the 2024 residential code as New Jersey adopted it. We build new masonry chimneys for homes that never had one and for additions. We also build them where an old chimney has failed all the way down and has to start again from a new footing. The same crew does the roof tie-in, flashing and crown. Most of what decides the job is fixed before the first brick: what you will burn, where the chimney meets the roof, and how deep the footing goes.

Do You Need a New Chimney, a Rebuild, or a Liner?

You need a new chimney when there is no sound chimney left to fix: the house never had one, the old one has failed to its base, or an addition needs its own flue. Most chimney problems are smaller.

  • No chimney, and you want a wood-burning fireplace or a wood stove: a new chimney, either masonry on its own footing or a listed factory-built system.
  • Brick failing above the roof but sound below it: a partial chimney rebuild, a smaller job.
  • Masonry in good shape, but the flue is unlined or its clay tiles are cracked: relining the existing flue.
  • A ceiling stain near the chimney: start with chimney leak repair; leaks usually start at the crown or flashing.
  • A rusted chase cover or rotting siding on a prefab chase: chimney repair and chase covers.
  • A fireplace that smokes or has cracked firebrick: fireplace repair.
  • A new home or addition where someone else is the builder: the chimney is one of the exterior trades we handle on new construction.

If the only goal is venting a new gas furnace, boiler or water heater, ask the HVAC installer how that appliance's listing requires it to vent before you price a chimney.

Masonry or Prefab (Factory-Built) Chimney: How the Two Differ

A masonry chimney is brick or block on its own footing with a code-required liner inside. A factory-built (prefab) chimney is a listed metal system, often in a framed chase, installed exactly to its manufacturer's instructions.

Masonry chimney walls must be solid masonry, or hollow units grouted solid, at least 4 inches thick nominal (IRC R1003.10). Every masonry chimney must be lined to suit the appliance: clay flue tile, a UL 1777 listed lining system, or another approved material (R1003.11.1). It carries only its own weight unless designed for more (R1003.8), so framing is built around it, not resting on it.

For a factory-built chimney, the manufacturer's listing is the rulebook. One serving a wood stove or other solid-fuel appliance must be a high-temperature system (UL 103 Type HT); one serving an open-combustion-chamber fireplace needs only the UL 103 residential rating, not Type HT; a factory-built fireplace needs the chimney listed with it (UL 127). A decorative shroud must be listed for that exact system. No section may run more than 30 degrees off vertical, with no more than four elbows. CSIA, the Chimney Safety Institute of America, warns that listed systems are often refitted with aftermarket parts that may not match the original listing.

A brick-faced chase is still a frame chimney. Where masonry veneers a framed chimney, the code requires through-flashing and weep holes (R1003.10.1). If a brick chase leaks, check for those along with the chase top.

Our trade is the masonry chimney, plus the roofing, flashing and siding around a chimney of either type.

What New Jersey Code Requires of a New Chimney

A new masonry chimney in New Jersey needs a footing below frost depth (3 feet in North Jersey), a top that meets the 3-2-10 height rule, an airspace to framing, a lined flue, a sloped crown with a drip edge, a cleanout at the base, and, on a wide chimney, a cricket.

New Jersey adopted the 2024 International Residential Code (IRC) on August 17, 2026; a complete application filed through February 17, 2027 can still use the 2021 code if it says so. The chimney rules below are substantively the same under either edition, and New Jersey's own changes to the chimney chapter are limited to clearance details.

  • Footing: concrete or solid masonry at least 12 inches thick, extending at least 6 inches past the chimney on every side, on undisturbed soil or engineered fill below frost depth: 3 feet in Mercer, Middlesex and every county north.
  • Height, the 3-2-10 rule: at least 3 feet above the highest point where the chimney passes through the roof, and at least 2 feet higher than any part of the building within 10 feet. The 10 feet is horizontal, so a nearby ridge or dormer often sets the height.
  • Clearance: a 2-inch airspace to framing where the chimney is inside the house or within an exterior wall, 1 inch where it stands entirely outside, filled only by fireblocking. New Jersey's amendment lets combustible material abut the chimney's side walls, as drawn in the code's clearance figure, where it is at least 6 inches from the inside of the nearest flue liner (the model code says 8). Framing still keeps the airspace.
  • Fireblocking: gaps where the chimney passes floors and ceilings are closed with noncombustible material fastened in place.
  • Crown: a concrete, metal or stone cap, sloped to shed water, with a drip edge and a caulked bond break around the flue liners. A rain cap or spark arrestor has its own rules only when one is installed.
  • Cricket: a small peaked roof section on the uphill side, required when the chimney is wider than 30 inches measured parallel to the ridge and doesn't meet the ridge.
  • Cleanout: an opening with a noncombustible cover within 6 inches of the base of each flue, its top edge at least 6 inches below the lowest inlet. Masonry fireplace flues that can be cleaned through the firebox are exempt.

Permits, Inspections, and Who Does Which Part

A new chimney needs a construction permit before work starts: New Jersey's Uniform Construction Code makes it unlawful to construct a structure without one (N.J.A.C. 5:23-2.14). The local construction official reviews the plans and decides what the job requires. NJ lists the application of liquid-applied lining material inside an existing chimney as ordinary maintenance; a new stainless or clay liner is not that item, so ask the construction office.

On a one- or two-family home, the town inspects the footing trench before the pour and the foundation before backfill, and work stops until each has been inspected. Ask to see both sign-offs.

New Jersey requires plumbing, electrical and HVAC work to be done by people licensed for it, other than a homeowner working on their own single-family home, and New Jersey's construction rules have been amended to require master hearth specialist work to be done by a certified person who signs the subcode application. Before the permit is filed, ask the construction office whether any part of your project needs that signature (the chimney, a fireplace, a stove or a factory-built system), and ask whoever signs to show their certification.

On our jobs, gas and electrical work goes to a licensed plumber and a licensed electrician we work with. Our NJ Home Improvement Contractor registration is #13VH12696700, and we carry general liability and workers' compensation insurance. An exterior chimney in a side yard may also need zoning review.

Size the Flue to the Appliance First

Decide what you will burn before the chimney is drawn. A flue can never be smaller in area than the connector from the appliance it serves (R1003.14).

Whether two appliances may share a flue is set by their listings and the mechanical and fuel-gas codes, and the licensed HVAC or plumbing installer decides. Two masonry rules are fixed: nothing may vent through the space around a liner (R1003.12.2), and separate flues need a bonded masonry wall at least 4 inches thick between them, unless two flues vent one appliance with liner joints staggered at least 4 inches.

Code height is a fire-safety minimum, not a draft guarantee. The Brick Industry Association notes that how well a chimney draws depends on the size of the fireplace opening, the flue area and the chimney's height together, so a chimney can need more height than the code minimum to draw well. It can pass inspection and still smoke.

How a New Masonry Chimney Goes Up, Step by Step

A new masonry chimney goes up in seven stages, with two inspections before the foundation is backfilled and the construction office's remaining inspections before sign-off.

  • Design. The appliance, flue size and the chimney's position against the roof come first; the height rule and any cricket depend on them. Then the permit application.
  • Footing. The excavation goes below frost depth (3 feet in North Jersey, 2 feet 6 inches in South Jersey), the trench is inspected, and the footing is poured.
  • Foundation to grade, inspected before backfill. Where masonry touches earth, the Brick Industry Association recommends Type M mortar.
  • The stack. Flue liners are set one section ahead of the brick in refractory mortar, the airspace to framing is kept clear, each floor is fireblocked, and cleanouts go in where required.
  • Through the roof. Base flashing runs at least 4 inches up the brick, and step flashing weaves into each course of roofing; counterflashing is set 3/4 to 1 inch into a mortar joint and laps the base flashing by at least 3 inches; a cricket is framed where required.
  • The top. A sloped crown with a drip edge and a bond break at the liners, with the liners projecting at least 2 inches above it.
  • The construction office's remaining inspections, then sign-off.

Poured concrete is not the only choice for the crown. The Brick Industry Association says prefabricated caps generally perform better than cast-in-place ones, and warns against feathering a cast cap thin at its edge.

Building a New Chimney for North Jersey Freeze-Thaw

New Jersey code rates weathering exposure Severe statewide, so a chimney here has to be built for freeze-thaw. Brick that soaks up water and freezes spalls its face. A crown that holds water cracks. Flashing caulked to the brick face opens up, and nor'easters drive rain into that joint.

That is why the Brick Industry Association recommends Grade SW (severe-weathering) brick for chimneys, with Type N portland cement-lime mortar above grade and Type S where higher lateral loads call for it. On an older house, matching new brick and mortar to the existing walls is the same work our crew does on masonry repairs.

How to Tell a Well-Built New Chimney From a Bad One

Five checks separate a well-built new chimney from a bad one; you can confirm several from the ground or from your permit paperwork:

  • A construction permit issued before any digging started, with the footing-trench and foundation inspections signed off before backfill.
  • A crown that overhangs the brick with a drip edge, slopes away from the flue, and has a sealed joint at the liner. A thin mortar wash with none of those is not what the code calls for.
  • Counterflashing let into the mortar joints, not caulked onto the brick face, and a cricket behind any chimney wider than 30 inches along the ridge direction that doesn't meet the ridge.
  • Weep holes at the base of any brick veneer on a framed chase.
  • On a factory-built system, the listing label in place and every part, including the shroud, from the same listed system.

CSIA follows NFPA 211, which calls for chimneys, fireplaces and vents to be inspected at least once a year. Treat that as a safety recommendation, and schedule the first chimney inspection after the first heating season.

What Changes the Scope of a New Chimney

Every new chimney is scoped from a site visit. These variables move the work most:

  • Height, which depends on the roof around the chimney and the number of stories it passes through.
  • Excavation and access: open ground versus a tight side yard or a deck in the way.
  • The number of flues and the liner type the appliances call for.
  • Blending brick on an older house versus new construction.
  • The roof tie-in: shingle, slate or flat roof, and whether a cricket is needed.
  • Interior work the chimney requires (openings through floors and ceilings), and who finishes them.
  • Licensed partner trades for gas or electrical work, and the permit.

Estimates are free and in writing, financing is available and explained at the estimate, and the work carries our written workmanship warranty. Call or request an estimate to start; the phone is answered by a real person 24/7.

What's Included

  • Masonry chimneys on footings below North Jersey's 3-foot frost line
  • Flue sized to your appliance, with a code-required liner
  • Sloped crown with a drip edge and a bond break at the liners
  • Step flashing, counterflashing and crickets tied into the roof
  • Brick selected to blend with the house on additions and older homes
  • Gas and electrical by licensed partner trades we work with

Chimney Installation — Common Questions

Do I need a permit to build a new chimney in New Jersey?

Yes. Building a new chimney is construction under N.J.A.C. 5:23-2.14, and construction needs a permit from your town's construction office before work starts. On a one- or two-family home, the inspector checks the footing trench before the concrete is poured and the foundation before it is backfilled, and work stops until each inspection is made. The local construction official decides what your specific job requires, including whether any part of it needs a master hearth specialist's signature.

How tall does a chimney have to be in NJ?

A chimney in New Jersey must extend at least 3 feet above the highest point where it passes through the roof and at least 2 feet higher than any part of the building within 10 feet. Worked example: your chimney exits partway up the roof, and the ridge 6 feet away (measured level, not along the slope) is 4 feet higher than the exit point. The chimney must reach 2 feet above that ridge, at least 6 feet above where it exits, not the 3-foot minimum. That height is a fire-safety minimum, and meeting it does not by itself make a chimney draw well.

How deep does a chimney footing need to go in North Jersey?

A chimney footing in North Jersey must sit below the 3-foot frost depth New Jersey sets for Mercer, Middlesex and every county north of them, including Bergen, Passaic, Essex, Hudson, Morris and Union. In South Jersey it is 2 feet 6 inches. The footing itself must be concrete or solid masonry at least 12 inches thick, extend at least 6 inches past the chimney on every side, and sit on undisturbed soil or engineered fill.

Masonry or prefab chimney: which should I choose?

Start from the appliance. A factory-built fireplace must use the chimney system listed for it (UL 127), so that choice is made. For a wood stove, either type can work. A masonry chimney needs a footing below frost depth (3 feet in North Jersey) and room for the stack. A factory-built chimney's support comes from the listed system's own parts and installation instructions. It must be the stove-rated system (UL 103 Type HT), built only from parts in its listing, and it often sits in a framed chase. We build the masonry kind and do the roof, flashing and siding work on either.

Can you add a chimney to a house that never had one?

Usually, yes. The first decision is inside or outside. A chimney built entirely outside the exterior wall needs a 1-inch airspace (2 inches if any part of it sits within the wall) and little interior work beyond the appliance opening, but it may project into a side-yard setback that needs zoning review. An interior chimney needs a 2-inch airspace, framed openings through each floor and the roof, and noncombustible fireblocking at every floor. Either way it needs a footing below frost depth and a flashed roof tie-in. The fireplace or stove it serves is its own scope. Gas and electrical work on our jobs goes to a licensed plumber and a licensed electrician we work with.

Can one chimney serve a fireplace and a furnace?

Yes, one chimney can hold several flues, each in its own liner, separated by a bonded masonry wall at least 4 inches thick. Whether two appliances may share one flue is set by their listings and the mechanical and fuel-gas codes, so the licensed HVAC or plumbing installer decides. The space around a flue liner can never vent a second appliance. Plan every appliance before the chimney is designed, because adding a flue later is far harder than building it in.

Does a new masonry chimney need a liner?

Yes. The IRC requires every masonry chimney to be lined, with a liner suited to the connected appliance's listing; the permitted options include clay flue tile, a listed lining system, or another approved material. Clay liners run from at least 8 inches below the lowest inlet, or from the top of the smoke chamber on a fireplace, to above the chimney walls, laid in refractory mortar. If you have an existing chimney that only needs a new liner, that is a reline, which is a different and much smaller job than building a new chimney.

Does New Jersey require rebar in a new chimney?

Not for seismic reasons on one- and two-family homes. New Jersey deletes the IRC seismic provisions for detached one- and two-family dwellings and townhouses, so the seismic reinforcing and anchorage that national pages describe do not apply to them. The model code itself requires no seismic reinforcing in Seismic Design Categories A through C. That does not mean reinforcing is never used. An engineered design can call for it, the Brick Industry Association recommends reinforcing a cast-in-place crown against shrinkage cracking, and the code's limits on corbeling (stepping brick out past the wall below it) still apply to every chimney.